Main > Linear drainage systems > Concrete channels Maxi >Series Maxi DN110

Concrete channels Maxi

Complete set: concrete channel series Maxi DN110 with cast-iron grating

Complete set: concrete channel MAXI DN100

Article - 04100
Length, width, height (mm) - 1000x190x230
Width of the hydraulic cross section (mm) - 110 (DN 110)
Load (kN) - 600
Application - roads, industrial zones, factories, storage terminals.

Complete set: concrete channel series Maxi DN110 with cast-iron grating and vertical spill way

Complete set: concrete channe MAXI DN110 with vertical spill way

Article - 0410009
Length, width, height (mm) - 1000x190x230
Width of the hydraulic cross section (mm) - 110 (DN 110)
Load (kN) - 600
Application - roads, industrial zones, factories, storage terminals.

Complete set: concrete channel series Maxi DN110 with cast-iron mesh grating

Complete set: concrete channel MAXI DN100 with cast-iron mesh grating

Article - 04104
Length, width, height (mm) - 1000x190x230
Width of the hydraulic cross section (mm) - 110 (DN 110)
Load (kN) - 600
Application - industrial zones, factories, storage terminals.

Application of concrete channels at industrial zones

Extremely robust reinforced drainage series Maxi DN110 are installed in the places with high traffic volume with load capacity not less than 60 tones (class E600 according to the European Standards DIN 19850).

Maxi 110 were developed for fuel filling stations, industrial zones, storage terminals, highways and other structures subjected to extreme mechanical loads.

Special attention should be paid to the way of fixing the gratings to the channel Maxi 110. The drainage has special slot for gasket with thread. The bolts screwed through the grating into the gasket. So the bolt makes no damage to the monolith of the channel. Due to this technical solution the body of the drainage will not be destroyed even by strong dynamic load.

By request of the client the set can be equipped with cast-iron galvanized grating.

Only complete set is for sale! the set consists of: 1 channel, 2 cast-iron gratings and the set of fixing bolts.

Complete set	Article, #	Load class	Length, mm	Width, mm	Height, mm	Height, mm	Pallet rules
Complete set: Drainage channel Maxi LV-11.19.23 concrete with cast-iron grating VCH-50 class E	04100	A-E	1000	190	230	70	18
Complete set: Drainage channel Maxi LV-11.19.23 concrete with cast-iron grating VCH-50 class E (with vertical spill way)	0410009	A-E	1000	190	230	70	18
Complete set: Drainage channel Maxi LV-11.19.18 concrete with cast-iron grating VCH-50 class E	04150	A-E	1000	190	180	60,5	18
Complete set: Drainage channel Maxi LV-11.19.13 concrete with cast-iron grating VCH-50 class E	04140	A-E	1000	190	130	50,5	18
Complete set: Drainage channel Maxi LV-11.19.23 concrete with cast-iron mesh grating VCH-50 class E	04104	A-E	1000	190	230	69	18
Complete set: Drainage channel Maxi LV-11.19.18 concrete with cast-iron mesh grating VCH-50 class E	04154	A-E	1000	190	180	59,5	18
Complete set: Drainage channel Maxi LV-11.19.13 concrete with cast-iron mesh grating VCH-50 class E	04144	A-E	1000	190	130	49,5	18

Trash boxes

Installation

Installation in asphalt surface

Installation of channels series Maxi
Load class	Base: width C thickness H, inch	Model of concrete base
D400	6/8	B25
E600	6/8	B25
F900	-	-

The channels are placed in the trench on the bottoming of hard concrete B15 10 cm thick. Side strengthening is made of concrete slants from the sides to the foundation 10 cm wide from each side.
The channel should be deep enough for the top of grating in the end of the installation be 3-5 mm lower than road covering.
The installation should begin with mounting the trashbox in the lower part of the plan, from which by means of cords there should be marked the line of laying of the channel.
The channels are connected line-on-line, that is why they have a slot on one side and tongue on the other. The junctions should not be additionally sealed.
When connecting the channels angularly the channels and the gratings should be cut and joint "в ус". The channel should be cut with handsaw with diamond disc, transversely to the channel capturing two sides at once.
In cases of installation of the channels in the asphalt coverage the gratings should be covered with strip of fibreboard or other material.
Asphalt areas should be laid with channels covered with gratings. It is inadmissible for asphalt paver or lorry to drive onto the channels.
For the concrete covering it is necessary to provide expansion joints - parallel to the drainage line in the distance 1.5-2 cm from each side and transversely in the distance of 5 m to each other.
When installing in the places of permanent vehicle traffic the channels should be necessarily laid on the concrete 10 cm foundation.
The drainage is connected to the sewer system through the trashbox by means of the branch pipe polyvinylchloride D100. The plug of the outlet should be taken off from the body of the trashbox before.
When connecting the drainage to the sewer system through vertical branch pipe without trashbox it is necessary to release the hole from the plug on the bottom. The gag should be drilled on the contour (drill diameter 8 mm) and with light strike of a hammer the plug should be removed. Branch pipe polyvinylchloride D100 should be placed in the hole. As the second variant of outlet there can be used an end cap with horizontal branch pipe polyvinylchloride D100.
Point storm water drainage are connected to the sewer system escaping the trashbox also by means of branch pipe polyvinylchloride D100.
It is necessary to clean the system periodically from trash. The cover should be taken off, the filter should be emptied. The frequency of cleaning depends on the conditions of use and is not less than 2-4 times per month.

Load classes