Main > Linear drainage systems > Plastic channels > Series DN200

Plastic channels

Plastic channel series DN200

Plastic channels series DN200. Linear drainage systems

Article - 8540
Length, width, height (mm) - 1000x260x200
Width of the hydraulic cross section (mm) - 200 (DN 200)
Load (kN) - 400
Application - streets, parkig areas.
Price: 810 Rub

See also:
— Gratings for these channels
— Accessories

Plastic channel series DN200 (reinforced)

Article - 8547
Length, width, height (mm) - 1000x260x200
Width of the hydraulic cross section (mm) - 200 (DN 200)
Load (kN) - 400
Application - streets, parkig areas.
Price: 1150 Rub

Application of plastic channels series DN200

Plastic channels series DN200 with operable width of the channel of 200 mm were specially created for the places to drain great volume of storm water and to survive loads of load class C. So it is used in the pedestrian areas, parking areas, access roads, sport structure, fuel filling stations, car washes and industrial zones.

Plastic channels are frost-resistant, which allows using them in the inclement climate conditions of Russia.

or such channels we offer special gratings: steel mesh gratings and cast iron gratings.

Name	Article, #	Load class	Length, mm	Width, mm	Height, mm	Weight, kg	Pallet rules
Drainage channel - 20.26.20 - plastic	8540	A-C	1000	260	200	4,0	56
Drainage channel - 20.26.20 - plastic (reinforced)	8547	A-C	1000	260	200	4,85	56

Drainage gratings for plastic channels series DN200

Steel mesh grating. Article - 2520

Length, width, height (mm) - 1000x236x33

Load (kN) - 125

Price: 1800 Rub

Cast-iron slotted grating. Article - 22303

Length, width, height (mm) - 500x236x14

Load (kN) - 250

Price: 910 Rub

Cast-iron mesh grating. Article - 22403

Length, width, height (mm) - 500x236x14

Load (kN) - 250

Price: 950 Rub

Grating stamped steel galvanized. Article - 2210

Length, width, height (mm) - 1000x236x10

Load (kN) - 15

Price: 1000 Rub

Gratings for channels series DN 200
Article #	Load class	Name	Length, mm	Width, mm	Height, mm	Weight, kg
2520	A-B	Drainage grating - 20.23,6.100 - steel mesh (galvanized)	1000	236	33	5,9
22303	A-C	Drainage grating - 20.23,6.50 - VCH-50 class C (mesh)	500	236	14	5,6
22403	A-C	Drainage grating - 20.23,6.50 - VCH-50 class C (mesh)	500	236	14	5,5
2210	A	Drainage grating - 20.23,6.100 - steel stamped (galvanized)	1000	236	10	3,2

Accessories

End caps are designed for installation at the beginning or the end of the channel.

In order to avoid displacement and noise at journey of cars, lit is possible to fix gratings to a channel with the help of antivandal fixing latches.

Installation scheme of protective insert

Prevents the ingress of leaves and other debris into the sewer pipe.

Name	Article, #	Load class	Length, mm	Width, mm	Height, mm	Weight, kg	Pallet rules
End cap - 20.20 - plastic	6854	-	-	-	-	-	-
Fixing for drainage channel - 20.26.20 - plastic	8505	-	235	30	20	0,25	-
Protective insert for channel	8008	-	-	-	-	0,08	-

Installation

Installation in asphalt surface

Installation of plastic channels series DN200
Load class	Base: width C thickness H, inch	Model of concrete base
A15	3.5/4	B25
B125	3.5/4	B25
C250	3.5/4	B25
D400	4/4	B25

The channels are placed in the trench on the bottoming of hard concrete B15 10 cm thick. Side strengthening is made of concrete slants from the sides to the foundation 10 cm wide from each side.
The channel should be deep enough for the top of grating in the end of the installation be 3-5 mm lower than road covering.
The installation should begin with mounting the trashbox in the lower part of the plan, from which by means of cords there should be marked the line of laying of the channel.
The channels are connected line-on-line, that is why they have a slot on one side and tongue on the other. The junctions should not be additionally sealed.
When connecting the channels angularly the channels and the gratings should be cut and joint "в ус". The channel should be cut with handsaw with diamond disc, transversely to the channel capturing two sides at once.
In cases of installation of the channels in the asphalt coverage the gratings should be covered with strip of fibreboard or other material.
Asphalt areas should be laid with channels covered with gratings. It is inadmissible for asphalt paver or lorry to drive onto the channels.
For the concrete covering it is necessary to provide expansion joints - parallel to the drainage line in the distance 1.5-2 cm from each side and transversely in the distance of 5 m to each other.
When installing in the places of permanent vehicle traffic the channels should be necessarily laid on the concrete 10 cm foundation.
The drainage is connected to the sewer system through the trashbox by means of the branch pipe polyvinylchloride D100. The plug of the outlet should be taken off from the body of the trashbox before.
When connecting the drainage to the sewer system through vertical branch pipe without trashbox it is necessary to release the hole from the plug on the bottom. The gag should be drilled on the contour (drill diameter 8 mm) and with light strike of a hammer the plug should be removed. Branch pipe polyvinylchloride D100 should be placed in the hole. As the second variant of outlet there can be used an end cap with horizontal branch pipe polyvinylchloride D100.
Point storm water drainage are connected to the sewer system escaping the trashbox also by means of branch pipe polyvinylchloride D100.
It is necessary to clean the system periodically from trash. The cover should be taken off, the filter should be emptied. The frequency of cleaning depends on the conditions of use and is not less than 2-4 times per month.

Load classes